Shopbot and Tormak: Difference between revisions

From makernexuswiki
Jump to navigation Jump to search
(Note on spindle speed.)
(4 intermediate revisions by the same user not shown)
Line 7: Line 7:
= Maker Nexus Equipment =
= Maker Nexus Equipment =


The Maker Nexus woodshop has a [https://www.shopbottools.com/products/standard ShopBot PRSstandard 48-48] with an effective work area of 48" x 48" for cutting soft materials such as wood and plastic. The shop has chucks for mounting 1/8", 1/4", 3/8", or 1/2" tools. There is no automatic tool changer. Spindle speed must be adjusted manually.
The Maker Nexus woodshop has a [https://www.shopbottools.com/products/standard ShopBot PRSstandard 48-48] with an effective work area of 48" x 48" for cutting soft materials such as wood and plastic. The shop has chucks for mounting 1/8", 1/4", 3/8", or 1/2" tools. There is no automatic tool changer. Spindle speed must be adjusted manually. Jog speed must be no more than 4 ips or the machine will lose position.
 
= Software =
 
To prepare your design for cutting you need to create "tool paths" for the target machine. In software you define the material your part will be cut from, the tools (bits) you will be using, and the speeds and feeds for each tool.
 
* V-Carve is provided by ShopBot to create toolpaths. A limited feature version is available for members to run at home to prepare their files for generating a cut file. Then you create the cut file on a full featured version at Maker Nexus. You can save a 2D file as .dxf and then import into VCarve.
 
* Fusion 360 can also create [https://www.autodesk.com/products/fusion-360/blog/getting-started-introduction-to-cam-and-toolpaths/  Toolpaths]. However the free version of Fusion 360 all the rapid moves (G00) to G01 as an incentive to upgrade to a paid version. So your cut file will take longer to run if you create it with the free version of Fusion 360.


= Techniques =
= Techniques =
ShopBot specific tips can be found at [[ShopBot tips]].


== Speeds and Feeds ==
== Speeds and Feeds ==

Revision as of 13:39, 22 May 2022

Device Manufacturers

  • ShopBot website - The classic CNC wood router. Tabletop to 4x8.
  • Iconic CNC website - Midsize CNC routers

Maker Nexus Equipment

The Maker Nexus woodshop has a ShopBot PRSstandard 48-48 with an effective work area of 48" x 48" for cutting soft materials such as wood and plastic. The shop has chucks for mounting 1/8", 1/4", 3/8", or 1/2" tools. There is no automatic tool changer. Spindle speed must be adjusted manually. Jog speed must be no more than 4 ips or the machine will lose position.

Software

To prepare your design for cutting you need to create "tool paths" for the target machine. In software you define the material your part will be cut from, the tools (bits) you will be using, and the speeds and feeds for each tool.

  • V-Carve is provided by ShopBot to create toolpaths. A limited feature version is available for members to run at home to prepare their files for generating a cut file. Then you create the cut file on a full featured version at Maker Nexus. You can save a 2D file as .dxf and then import into VCarve.
  • Fusion 360 can also create Toolpaths. However the free version of Fusion 360 all the rapid moves (G00) to G01 as an incentive to upgrade to a paid version. So your cut file will take longer to run if you create it with the free version of Fusion 360.

Techniques

ShopBot specific tips can be found at ShopBot tips.

Speeds and Feeds

Wikipedia has a good page on speeds and feeds. In particular, you can get the cutting speeds for many materials using a high speed steel cutter. http://en.wikipedia.org/wiki/Speeds_and_feeds Missing from the Wikipedia table is Wood. The Cutting Speed for a soft wood, such as pine, is 1000 feet per minute.

There is a recommended speeds and feeds calculator at http://www.custompartnet.com/calculator ... d-and-feed The calculator needs Feed per Tooth. We were told to use the following values:

  • Aluminum: 1/100th the bit diameter
  • Wood: 1/50th the bit diameter
  • Foam: 0.1

Plunge speed should be about 1/3 the feed rate.

Most router bit specs have feed recommendations. Amana router bits also specify the material type. They have bits for wood, plastic, stone, metal, etc.

Problems when cutting

If your wood part smokes, then either increase the feed rate or slow the spindle RPM. If you hear screeching, they you are feeding to fast - or too slow. Try slowing the feedrate first. If that doesn't work, then increase the feed rate a bit.

Supplies

Bits

The shop keeps a few bits on hand for classes and for resurfacing the spoil board but you should purchase your own bits to avoid damaging the shop's tools and ensure consistent results for your projects.

The more flutes a bit has, the more heat it generates. Typical flutes for materials:

  • Plastic: 2
  • Wood: 1 or 2
  • Aluminum: 2
  • Steel: 4

CNC router bits are different from handheld router bits. They are driven through material by a rigid gantry whereas handheld router bits follow a path using a guide bearing. Be sure to buy the right kind of bit.

Dan-Mar Tools is a good source of bits 907 American Street, San Carlos, CA 94070 Phone:(650) 591-2651For cutting pink foam, Matthew had a four inch long bit that was about 0.5 inch in diameter. The flutes were almost like a rasp on it. He said it would just rip thought the foam at very high speed. Great for a roughing pass.

You can also purchase bits online from Amazon and other retailers. Carbide bits last longer than high speed steel but are much more expensive and brittle (don't drop them!). Some manufacturers offer complementary sets of bits at a modest discount to get your collection started, such as MakerMade, Whiteside, and Freud.

Materials

Pink Foam

I bought 4x8 sheets of two-inch thick pink foam insulation at Home Depot. Not every HD carried it. The sheets where scored half way through every 18 inches. This material cut extremely well. I sprayed the finished piece with shellack. For a more spooky effect I sprayed it with gray paint and the material started to dissolve away a bit.