All public logs
Jump to navigation
Jump to search
Combined display of all available logs of makernexuswiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).
- 00:50, 30 December 2023 Jschrempp talk contribs created page Sawgrass SG1000 Sublimation Printer (Created page with "Prints onto special paper and that is applied to a surface with heat. Fabrics and objects that lay flat can use the heat press. Shaped objects need a compression sleeve and the oven. This process will print well on dark fabrics. A good source of supplies: [https://www.heattransferwarehouse.com/ Heat Transfer Warehouse]. They are not crazy expensive, but not cheap.")
- 15:25, 28 December 2023 Jschrempp talk contribs uploaded File:Rotating laser joint.png (example of a rotating joint with a stop point)
- 15:25, 28 December 2023 Jschrempp talk contribs created page File:Rotating laser joint.png (example of a rotating joint with a stop point)
- 14:09, 21 December 2023 User account Ally.kraus talk contribs was created by Jschrempp talk contribs and password was sent by email
- 15:11, 11 December 2023 Jschrempp talk contribs blocked 120.11.91.185 talk with an expiration time of indefinite (anonymous users only, account creation disabled)
- 15:07, 11 December 2023 User account Allyk talk contribs was created by Jschrempp talk contribs and password was sent by email
- 20:53, 6 November 2023 Jschrempp talk contribs created page Advice: Wood Glue Ups (Created page with "= One man's opinions = [https://www.youtube.com/watch?v=Wmw5rayNIV4 This video clip] has some good general tips to start with. Don’t over-clamp the joint. I’m right-handed, so I use the left-hand cue i.e. the turn the clamp with my left hand just enough. That gives me a good feel for the tightening. There is a lot of gluing in an end grain cutting board. So, make the clean up easy by applying just the right amount of glue (as above). If there is squeeze out, resist...")
- 10:45, 4 November 2023 Jschrempp talk contribs created page Drum sander tips (Created page with "In the shared shop environment you have to assume every tool is slightly out of adjustment unless you adjust it as you are starting your job, and assume it will be out of adjustment the next day you need to use that tool. The drum sander should be adjusted slightly tighter on the motor side. On a project desiring high precision and parallel you should make the adjustment for your job and hopefully put it back when you are done. For jobs narrower than 16” not req...")
- 15:18, 3 November 2023 Jschrempp talk contribs created page Wood preparation tips 1 (Created page with "= Precision is key = 400px|right|I recently finished an end grain cutting board that I recently finished. In response to a couple of questions from other members who saw me in the process of building it, here are some build notes that may be of help. I am not going to describe how to build edge grain cutting boards here - there are enough videos on YT that describe how to do that. Instead, I would like to focus on “precision” since even t...")
- 15:00, 3 November 2023 Jschrempp talk contribs uploaded File:CuttingBoard.jpg (Precision end grain cutting board)
- 15:00, 3 November 2023 Jschrempp talk contribs created page File:CuttingBoard.jpg (Precision end grain cutting board)
- 10:44, 28 October 2023 Jschrempp talk contribs changed group membership for Kellybyrd from administrator to (none)
- 10:44, 28 October 2023 Jschrempp talk contribs changed group membership for DanR from bureaucrat and administrator to (none)
- 10:44, 28 October 2023 Jschrempp talk contribs changed group membership for Ajohnson from administrator to (none)
- 19:53, 19 September 2023 Jschrempp talk contribs created page Changing Barudan Frame (Created page with "Q: I have some material that does not fit into the standard textile frames - I saw some yellow metal frames that look like they work, but no idea how to get them into the machine. :A: Undo the 4 black turn knobs. Slide the pantograph frame out. Slide the clamp frame in. Tighten the 2 centre black knobs. Make sure before you tighten the knobs that the frame is sitting right down and the two little buttons are poking through the holes by the knobs. Reverse the procedure...")
- 19:53, 19 September 2023 Jschrempp talk contribs uploaded File:Barudan knob 6.jpg (knob 6)
- 19:53, 19 September 2023 Jschrempp talk contribs created page File:Barudan knob 6.jpg (knob 6)
- 19:52, 19 September 2023 Jschrempp talk contribs uploaded File:Barudan knob 5.jpg (knob 5)
- 19:52, 19 September 2023 Jschrempp talk contribs created page File:Barudan knob 5.jpg (knob 5)
- 19:51, 19 September 2023 Jschrempp talk contribs uploaded File:Barudan knob 4.jpg (knob 4)